Month: November 2010

Motorsport at any level is hugely enthralling, but the costs are prohibitive for the vast majority of enthusiasts. There are, however, a few ways round this and it is possible to do a day’s competition for less than the cost of a full tank of fuel.

The fastest cars in drag racing accelerate from 0 to 100mph in 0.8 of a second, and exceed 330mph in ¼ of a mile, but they will spend 500 quid on fuel for each run, followed by replacing most of the 50 grand engine. By comparison The Slow Car Club take bangers usually costing less than 500 quid up the track at Santa Pod on Run What Ya Brung days, entry costs 35 quid for a whole day of driving flat out. It doesn’t matter how fast the car is because after the first few runs you start trying to beat your own personal best time, it is highly addictive and lots of fun.

If you have ever fancied rally driving but haven’t got a rally car and baulk at the £300 entry fee for even the smallest of events then drop down a few gears and look at Production Car Trials. As the name suggests the cars are standard and there are classes for different engine sizes and engine/drive configurations, 4x4s are banned. The set up is simple; take a muddy hill with a few obstacles, mark out a challenging twisty course and see how far you can drive a car up the track before getting stuck. About the only modification you can make to the car is dropping the tyre pressures. The tracks are divided into 10 sections and you get penalty points depending on how badly you do, if you manage to get all the way up then you have no penalties and its a clear run. The skill required is remarkable and it is easy to get utterly immersed in the task of coaxing your banger that extra few inches up the track, it’s just as addictive as high speed track racing and highly recommended.

Another variant on the rally theme is the 12 Car Event, this is a navigational event run on public roads so speeds are modest. A route is issued to the drivers at the start line and timekeepers are stationed at the end of each section, the skill is in the teamwork between the navigator and driver to ensure the best route is taken and speed optimised to make sure the car arrives at precisely the right time. It’s very competitive and requires self control as much as car control, going to fast is as bad as too slow.

You have probably seen some footage of cars being expertly drifted round a very tight course laid out with cones in a car park. This is Autotesting and is a measure of drivers skill against the clock whilst negotiating hairpin bends, reverse parking and tight slaloms. You’ll need good tyres to get the best out of the car but for road car classes that’s about the only thing you can change. Precision and pace are needed in bucket loads, you think you can handle a car – this will make you think again!

But if driving flat out round corners is high on your needs list then consider Hill Climb or Sprints, this is usually on race tracks and does require a race licence so the costs start mounting but it does mean you can drive at high speeds on real circuits. The idea is simple – to get fro the start line to the finish line as fast as possible and its wonderful to watch as there is often old F1 machinery operating in the upper classes. If you wonder what the difference is a Hill climb is up hill and a sprint is on the flat, more or less.

In fact there is a surprising wealth of cheap motorsport opportunities in this country, if you are handy with the spanners then there is Grass Track (sprint races in a field), Comp Safari (rallying for grown ups), economy runs (more fun than you might think) and even real circuit racing can be done on a budget of less than £3000.

Currently I am liking the idea of buying a bargain banger for less than £500 and seeing just how many events it can do in a year. Probably something old, maybe another Jag, or a 2CV, or a Maestro, the more un-motorsport the better, maybe a diesel. Anyone fancy joining in?

Cresting a tree lined hill in majestically controlled opulence, I marvel at the sheer volume of technical excellence dedicating its existence to making my drive a simply fabulous experience.

The Rolls Royce Ghost is unusual in RR history as it is expected that owners will drive it, for some of the time anyway. Traditional RR theory has it that owners always travel in the back and so driver aids were kept to a minimum, but the Ghost has a plethora of modern technological wonders to make driving easier and more pleasurable.

As with many cars today it has an electric handbrake. But it performs a more sophisticated role here than on a humble peasant hatchback, it holds the car at rest until the accelerator is pressed when it is seamlessly released, leaving the switch in this mode means that the brake is automatically applied when at rest and if the driver exits for a quick ‘comfort break’ in the hedges the gearbox is automatically put into parked too. This is surprisingly useful when swapping drivers on long trips and the such like.

Gear selection is elegantly simple with Park, Reverse, Neutral and Drive being the only options. It goes without saying that the system analyses your driving style and adapts to suit, almost anticipating your desire for a gear shift before you know it.

The head up display shows the current speed limit derived from the on-board camera and some very clever image recognition systems that look for road signs, this means it can pick up temporary and new speed limits which is something sat-nav based systems have no chance of dealing with. This is linked to the adaptive cruise control so you never need get caught for speeding ever again. The system also notices white lines and if it detects the driver drifting out of lane without indicating it will discretely vibrate the steering wheel.

But I found driving it a surprise for all the wrong reasons. For sure the power delivery is smooth and effortless, with a wealth of thrust available throughout the rev range, and the ride is supple yet responsive but a tad more twitchy than Roller’s of old. The cabin is well insulated from outside noise, shutting the door is like closing a granite lid on a padded tomb, but unfortunately there was a fair amount of road noise transmitted through the car itself, particularly tyre noise. This might be more noticeable because of the near total lack of other noise, yet having driven older offerings from this legendary brand where there was no noise at all at moderate speeds I do think this is genuine and a step in the wrong direction. Although it has to be said that with the Crewe built cars wind noise, scuttle shake and a tendency not to go in precisely the direction intended were always features, which have thankfully all been dispelled in the new models.

So if the new car is better insulated, more solidly built and has better suspension how come there is more road noise? Well, I think this may be due to the affliction that most modern cars suffer from; excessively low profile tyres.

The thing driving this move towards rubber bands is not solid engineering but the fickle whim of fashion. Even Range Rovers run on 40 profile tyres now, which is quite frankly ridiculous. Low profile means the tyre cant adapt to the road surface and makes for a harsh ride and a tendency to skitter on all but the smoothest of surfaces. Tyres are an important part of the suspension system and making them too stiff is like welding girders onto the springs. You’ll never see an F1 car on low profiles.

I would dearly love to drive this magnificent car on better tyres, then I am sure it would effortlessly waft in silent majesty, just as it should.

The same basic principals apply to both XJ-S and XJ6/12 cars. First up which car to go for.

The V12 in 5.3 form is fantastic on the race track with a 6500rpm rev limit and over 300bhp readily available, although the standard cooling system is dire. The first V12s had flat cylinder heads and can be tuned up to over 600bhp (at great expense), later models had the High Efficiency HE heads which limit power but drastically improve fuel ‘economy’ and is still good for well over 400bhp. Early cars had a 4 speed manual gearbox as an option but these are hideously expensive, most have the immensely tough GM TH400 auto box which can also make a good race box when fitted with American drag racing parts. I raced an auto with manual override and it was superb. The last XJS cars had the 6 litre V12 with a 4 speed 4L80E auto which can be modified to work in manual mode either mechanically or electrically (paddle shift style), but these cars are rather expensive.

The 6 cylinder engines in the XJ-S were either the AJ6 in 3.6 or 4.0 forms or the four valve AJ16 version of the 4.0. All are powerful with over 300 bhp quite feasible. Available with either the 5 speed manual or the 4 speed ZF auto, again the auto can be modified for racing but the manual is a simpler option.

Basic track mods:

Brake pads, race brake fluid, jack the bonnet open an inch and fit good tyres. Give it a full service and off you go!

The more complicated version:

All cheap cars are rotten, so plan for welding. The front subframe which holds the engine up and holds the suspension on rusts from the middle out, good second hand ones are over £250 and quite a big job to change, so make sure you get a good one. The smaller cross member under the radiator also rots out but can easily be replaced with a strip of suitable metal and is not a deal breaker.

The front of the sills rots behind the ally splash guard but is reasonably simple to repair. The back of the sills is a very complex construction and includes the rear axle radius arm mount, this is a sod to rebuild but for racing it can be simpler to just cut the whole lot out and weld in a simple sill and convert the radius arms to a ‘cotton reel’ bushed rod that is mounted into a fabricated box intruding into the rear passenger foot well. This mod cuts out some weight too and also improves axle location.

When viewing a car pull up the rear seat base, rain water leaks in from the quarter light seals and pool in the seat base/ inner sill area. The race car solution to a rusty bottom is to cut out the set base and weld a simple plate over it. Also check the front foot wells where water from leaking screen seals can pool and rot the floor. Many cars have been undersealed which is unhelpful as the rot starts from the inside of the car and the underseal can hide it from inspection.

Mechanically the cars are strong, but bushes, bearings and ball joints wear. For racing I replace bushes with polyurethane and budget for new bearings and ball joints. Brakes get extremely hot so we use BNS grease in the wheel bearings which copes with the heat. The gearbox mounting is a cunning and complex unit which will be worn and make clonking noises when driving hard but can be replaced with a simpler rubber mount. The steering rack has very soft bushing so fitting pollybushes sharpens up the steering considerably, some cheapskate racers just limit movement on the bushes by simply putting tie wraps round the bush edges!

The cooling system on V12s is dire, I flushed the accumulate rubbish out then fitted coolant made of about 1% water wetter, 10% anti-freeze and 89% water which has better heat transfer ability. Then I removed the visco fan and associated heavy bracketry, the fan cowling and the original electric fan. I fitted a large electric fan instead as the fan is only needed in the pits. Jacking the bonnet open an inch lets the hot air out which is just as important as letting cold air in.

The brakes fade horribly on track, I used EBC Yellow Stuff race pads and Motul RBF600 brake fluid. The fluid is vital, it has a higher boiling point but has to be changed more regularly. To get a bit more cooling air round the rear inboard brakes I took the access plates out of the boot and removed the boot seal to let the hot air out, another approach is to cur the boot floor out completely which further improves cooling and makes access much easier to the rear axle as well as saving weight.

Weight loss is key, the sound deadening is everywhere and it is a good days work ripping it out. A tar based substance is glued onto the floor and has to be chiselled off. The interior heater system is very heavy and can be largely thrown away, although leaving the drivers side screen fan helps demisting. I used RainX anti-fog on all the glass to prevent misting, much lighter solution than a heater. The standard XJ-S seats only weigh 7kg so make a good cheapskate racers choice. Door lock solenoids can be junked to save 2kg, but the door cards weigh naff all so leave them in. I would also leave the electric mirrors on as they are less than 1kg each and work very well.

The centre exhaust silencer can be replaced with a straight through tube for a few more bhp and less weight. The standard intake airbox is a little restrictive and the trumpet can be cut off and a larger hole formed with a radiused edge, it is vital to get cold air to this and running ducting from the headlight surround works well. The middle headlights on quad light models can be removed to make an excellent cold air intake point, although some bodywork has to be cut out to get into the engine bay. The standard paper air filters work well when new, no need for expensive sponge filters.

The engine oil needs to be able to cope with high speeds and temperatures, I used Castrol RS which is now superseded by Castrol Edge. The other fluids have to be changed for quality higher performance versions too, including power steering, gearbox and differential.

All XJ-Ss had and LSD as standard, the 6 pot models had the lower 3.54:1 ratio needed for racing and is a straight swap to replace the overly high V12 item.

With the car lighter it will sit stupidly heigh on its springs. Eibarch make a suitable race springs but they are pricey. I cheated slightly by using the Jaguar ‘Sports Pack’ springs from a 3.6 model on my V12 which worked out just right. Adjustable front dampers are a handy mod and can be tweaked to suit different circuits – hard for flat ones like Silverstone and softer for less even ones such as Croft.

Fitting 50 profile tyres on standard wheels drops the gearing a tad more and lowers the car a bit too. Buffing the tread down to 4mm will stop them going off due to heat build up, this maintains grip levels and actually improves wear rate. I used Toyo Proxes T1R tyres as they were mandated by the race series, and they seemed to work well even in heavy summer rain.

You may wonder about roll cages, but if the car is ever used on the road I would avoid them because of the injury risk from hitting a steel bar next to your head in a collision. Cages work well when the driver is secured in a race seat with a race harness and wearing a crash helmet. The Jags are strong cars anyway so a heavy cage is of questionable benefit unless racing.

All that remains is to fit a race harness to hold you steady and a race steering wheel to speed up response and it’s time to head for the track to have more fun than is decent.

Check out these web sites which I have found very useful:

http://www.jagracing.co.uk/index.html

http://www.xjs6000.cc

http://www.jag-lovers.org

http://www.mig-welding.co.uk/

The chances are you have already heard about the ‘Saturday Club’, a band of enthusiastic engineers who designed the stunning Jaguar XJ220 in their own time just because they had a burning desire to make their dream into a reality. But what happened after the concept was unveiled and why did the V12 get dropped in favour of the Metro 6R4 engine?

The original spec had the Jaguar V12 powering a 4WD system, the engine would be based on the race versions which were doing rather well in GT cars such as the 7 litre XJR9. The V12 engine also saw life as the 6 litre 450bhp motivation in the XJR15 road car. In fact Jaguar made 6 litres the standard displacement for the V12 in the last XJS and the XJ12, which soldiered on under increasingly stringent emissions regs until 1997 (X305).

The XJ220 concept had a 6.2 litre variant which had been producing a reliable 550bhp+ on test, it had been run at full power for extended periods of time and performed well under all manner of arduous test conditions. But the Friday before the 1988 NEC motorshow début the over worked engine unexpectedly seized, with no time to fix it the show car that thousands ogled at that year (including myself) had to be pushed onto the stand. Not a lot of people know that.

The car was simply stunning and orders poured in. So the next step was to put it into series production and the job was given to TWR who already had strong links with Jaguar. At this point things started changing and customers start cancelling orders, partly due to the recession and partly due to the spec change.

The original concept was declared too heavy, but at 1560kg it was still a good 200kg lighter than the lowest spec XJS and stacks up well against modern supercars. Curiously the Jaguar V12 was declared unfit for emissions, even though it was managing perfectly well in the XJR15 road car and the 546bhp Lister storm, as well as in lower state of tune in the XJ12. The 6R4 engine designed and developed by BL competition team had been acquired by TWR had proved a reliable and powerful lump, not only powering Metro 6R4s but also some of the Jaguar GT racer cars such as the XJR10, and was modified to get it through emissions regs and slipped in place. Extensive development of the engine was conducted on public roads in secret by grafting the whole XJ220 back end with the engine, gearbox and suspension, into a normal looking Ford Transit van (Now owned by Goodwood). I am sure this change from Jaguar V12 to TWR V6 was in no way motivated by any financial advantage to TWR for using their own engine. TWR still have the service contract for these cars, with costs totalling many thousands each time, providing a useful revenue stream to this day.

But with this engine the production car failed to meet its 220mph ambition, 217mph was achieved only by removing the wing mirrors and other tweaks.

Traditionally the problem with turbo engines is keeping the intake air cool at full load, as the turbos compress the air it gets hot and can easily exceed 100C. Hot air is less dense and reduces power. In a race a turbo engine can work well, as the intercoolers have a chance to cool down every time the car brakes for a corner, but when testing maximum speed the engine is flat out constantly and the heat just builds and builds. This is where a naturally aspirated engine has an advantage, the V12 had been run regularly in competition at power levels above 600bhp, in fact the XJR12 race car managed 750bhp from its 7.4 litres. So surely this would have been a more logical choice for a high speed super car?

Then there is the matter of the 4wd system, this was a version of the Ferguson Formula as seen on the Jensen FF. Ferguson research was another company offering engineering services to the car and motorsport industries, in a similar way to TWR. Ferguson would later be bought out by the mighty Ricardo organisation in 1994, and Ricardo would later take on a lot of Jaguar engineering work. Whether TWR saw the Ferguson involvement as a threat is unknown, but dropping the FF 4wd system meant that TWR had sole control over the whole project. In engineering terms the 4wd system has many advantages and the weight penalty is relatively small, as proved by later Lamborghinis.

What ever the real reasons for the changes, the car’s weight dropped by about 200kg which helped in cornering but did nothing for it’s main selling point – top speed. It also made it a lot cheaper to make, which must have been a consideration.

With many orders cancelled and built cars selling significantly under their list price the project lost a little of it’s shine. Many cars are still locked away with delivery mileage only, and in 2007 two unused shells were discovered in Jaguar’s Browns Lane factory when it was being cleared for demolition.

I am sure the decisions made at the time were based on sound judgement, but I cant help but wonder what would have happened if they had stayed with the original concept. Certainly a 750bhp V12 and 4wd would have giving it something in the order of 250mph capability and made it faster in a straight line than a McLaren F1. Maybe in some alternative universe they did just that, and the magnificent Jaguar matched the dreams of the Saturday Club and is the legend that it deserves to be.

I was testing a compact SUV the other day, it’s spec sheet fits in nicely with the current competition; about 240bhp in a 1400kg car, 4WD and 0-60 in the region of 7.9s. Although this may not be earth shattering performance by modern standards it set me thinking, about two decades ago I was working on a car that some of you may of heard of; the Escort Cosworth.

Now the Cossy set the world alight with its ‘blistering performance’, even that bloke Clarkson had one of his own and spent far too long telling everyone. Part of the Cossy legend comes fro the fact that in full rally cross tune it could hit the dark side of 600bhp, but even the standard version was in reality rather quick.

But now the Focus five pot has more than 300bhp and luxury saloons must have 500bhp to be a serious contender. Things have clearly moved on, but surely an old quick car is still a quick car? If I hopped into a Cossy today would I be bored rigid with it’s hum drum performance?

So I did a highly un-scientific poll on Twitter, asking people what felt quick to them, and the results were remarkably consistent, although that might just be an indication of the type of people who follow me!

Allegro fan extraordinare @OneCarefulOwner commented “the goalposts have moved in a major way; my Maxi 1750HL had a blistering 96bhp, nowadays small diesels have more grunt.”

@racing_waiting pointed out that defining quick was a well trodden path “tricky question, drivers republic struggled, imotor struggled, road my previous mag stuggled.”

On the subject of the old XR3i @HairyCalahan observed “times have changed. expectations too. xr3i fine for it’s day”

But getting down to numbers @vHenryk considdered that “pretty much. A ‘sports car’ doesn’t have to be a ridiculously expensive 0-60 in less than 5 secs thing to deserve the name.”. Whilst @torquespeak said “Puma convinces me anything above 120 has a decent shot. 8 secs to 60 not first degree rapid but a hoot on the twisty bits!”

Of course power and weight are only part of the storey as student and car nut @MrPA sugests “On a decent road anything can be fun. I have a few corner-filled favourites which are brilliant in my mum’s 1.2 Clio (75bhp!).” a fair point and one echoed by @cotswoldracer “Indeed , my old AX GT 700Kg & 85bhp , and going by memory about the same as my 145 in terms of acceleration (8ish secs to 60), my Alfa 145/950kg/150bhp quick-ish , another 35 bhp would make it even more fun :)”

@carpunk observes the importance of weight in its own right “Guess 100hp in a 1000kg car will always feel much quicker than 250hp in car 2x the weight because of inertia, braking mass etc “ and @jonbradbury agrees “I think modern expectations have increased, & so has most weights. Though 160hp in 1T 944 shifted lot better 115hp Gti & the 115hp GTi shifted better than the 115hp XR3i.”

The consensus seemed to be that a ‘sports car’ of between 1 and 1.5 tons should have between 180 and 250bhp.

Which brings up some interesting points, firstly that a lot of ordinary family cars are actually high performance sports cars, and it may well be that the only reason that they are not regularly parked in hedges and Armco is the astonishing amount of technology dedicated to combating incompetence behind the wheel.

But going back the that point about the way cars feel, this fantastic driver assistance seems to have come hand in hand with a duller edge to the driving experience. Back in the day a sports car would engage and entertain the driver, not only with its performance but also with its ability to snap back and slap the unwary in the startled face. Putting your foot down in a high powered car not only thrilled but also surprised many a driver when glancing at the speedo to see the needle significantly further round than expected. Over enthusiastic cornering could result in the car suddenly swapping ends or having less wheels on the ground than is healthy. Motoring enthusiasts call this sort of thing ‘fun’, but unfortunately normal people call it dangerous, and so because there are more of ‘them’ buying cars than there are ‘us’ cars have become less dangerous, and sometimes less fun.

But from an engineering point of view fun and safe can co-exist. Some manufacturers have cottoned on to the fact that whilst safe and dull is best for the mass market there is still a significant market for thrilling cars, and having driver aids set to only come in when disaster is otherwise inevitable yet allowing a reasonable degree of sideways progress makes good sense.

For instance if you turn off the traction control on a Jaguar XKR you can light up the tyres and do doughnuts, but you will still struggle to accidentally oversteer backwards into the vicars rose garden because the system is still active and helping the driver achieve their intended trajectory. I have driven one with the traction control completely removed, and to say one needs ones wits honed and ready for extreme service is an understatement, it’s not fun on a wet B road – it’s simply scary.

Maybe 500bhp is fine when controlled by modern electro-wizardry, but has the same thrill factor as a raw 200bhp in a car with no aids at all. So how much power does a sports car need? Well it would seem the definitive answer is ‘it depends’.

Brakes are all about heat, and ditching as much of it as quickly as possible, they work by converting the cars speed energy into heat energy which is then taken swiftly away in the air streaming through them, in theory. But a big car at high speed has an awful lot of energy; for instance getting a big car to do an emergency stop from high speed might put the equivalent of a thousand bhp through the brakes make the discs glow red.

There are two basic types of brake, drum brakes get their name from the drum of steel with curved shoes inside that are pushed outwards against the inside of the drum when the brake pedal is pushed. These can be found on the back axles of cheaper cars and are quite frankly a bit pants; the braking force is limited by the drum wanting to explode, plus the pistons are small and the pressure pushing the shoes out into the drum is similarly small.

By comparison disc brakes can exert a much higher force onto the disc without risk of it failing.

It uses a disc with a set of pads held in a calliper that are forced against both sides of the disc when the pedal is pressed, generating much more force.

In both cases the disc or drum part is attached to the wheel hub so it rotates with the wheel and the pads or shoes are held stationary on the axle, or strut, or what ever dangly bits are attached to the suspension.
All brakes work by friction, pressing a pretty darn tough pad of friction material against the spinning metal, the harder the friction material is pressed against the metal the more friction is produced and the greater the braking force.
Brake systems use a special type of high temperature hydraulic oil to drive the pistons which push the friction material into the disc or drum. At the pedal end there is another piston in the master cylinder which is connected by hydraulic brake pipe to the slave cylinders at each wheel. In some cars the brake force is artificially increased by a servo directly connected between the brake pedal and the master cylinder, this uses vacuum from the intake manifold to move a large diaphragm when the brake pedal was pressed, as the pedal moved down small holes in the servo control section are progressively uncovered which applies more vacuum to the diaphragm which in turn applies a greater force to the master piston of up to four times the force at the pedal.

Some cars with Anti-lock Brake Systems (ABS) use a powerful electric pump to do this instead. The ABS system measures wheel speeds and if it detects that a wheel is slowing down faster than a safe limit then it knows that that wheel is about to start locking up, so it lets the brake pressure off the individual wheel by opening a solenoid valve in the ABS valve block, just for a tiny fraction of a second until the wheel frees up just enough to know it wont lock. You can feel this when it happens as a sort of buzzing or vibration under the brake pedal. ABS allows maximum braking force without the risk of skidding. But if you are going to fast then you are still going to crash no matter what the brakes do.
The fierce heat generated from heavy braking has to be dissipated into the air which is why race cars have ducts taking fresh air from the front of the car to the disc centre, the hot air then has to go somewhere and the design of the wheel should allow it to escape readily. To get more heat into the air some discs are vented with radial channels cast into the disc to draw air from the centre outwards, some discs also have small holes drilled through for even more ventilation but these can lead to cracks starting unless they are made very well. Groves on performance discs can help remove the tiny gas layer that build up between the pad and disc sometimes and increase pad bite, the down side is that they can increase pad wear when used aggressively.
The brake size needed on a car depends on its weight and how fast it is likely to go, more powerful cars can more readily get up to higher speeds they need bigger brakes. Bigger pistons and a larger diameter disc make better brakes. Also if the brakes are going to be used for long durations, such as when racing, there is less time between brake applications for them to cool down adequately, this is where vented disks can be a real benefit.
All that heat soaks through the system into the brake fluid and although it is engineered to work at these very high temperatures in extreme cases the temperature can get high enough for the oil to boil, this generates gasses which compress easily and make the brake pedal feel very soft. This is brake fade and in really bad cases the brake pedal can sink to the floor with very little braking force generated, pumping the pedal up and down a few times can sometimes help but basically if the brakes fade on a race track then the standard procedure is to crash. That is why on roads with long descents the car’s speed should be controlled by using a low gear and engine braking rather than holding the brakes on for extended periods.

Most brake fluid absorbs water which boils and fades much more easily which is why it must be changed every few years to stay safe. Silicon based fluid is different and doesn’t absorb water but moisture still pools inside the system and needs flushing through every few years, it’s also a bit more squashy than mineral fluid making it unsuitable for fast acting ABS.

Brakes are often overlooked and any wear only becomes apparent at the mot or in an emergency stop. The trouble is that they have a hard life and can disintegrate with the friction material splitting off the steel backing or wearing down to nothing unnoticed, and they usually seem to work fine right up to the point were they don’t work at all and you crash. Maintenance and regular inspection is vital.

Larger brakes with a greater surface area to dissipate the heat into the air can cope with harder use but very large brakes need large wheels in order to fit. But all the force generated by the brakes has to be transmitted into the road by the tyres, so if the brakes are already capable of braking traction then there is little point upgrading them before upgrading the tyres. As ever the best solution depends on how the car is to be used.

Technology is fundamentally changing journalism and will ‘kill off’ the traditional idea of a journalist, or so I’m told.

If you think about it the traditional model of journalism has a very few journalists talking to the many readers much like the Queen addressing the nation, but with more queens. This may be because the traditional methods of mass communication, papers and books, was very expensive, time consuming and required specialist skills. But also because a small elite had vested interests in controlling information to a greater or lesser extent.
However now anyone can communicate to potentially the whole world, more or less for free. Everyone is a journalist, albeit not necessarily a very good one.
First the internet democratised information flow, but now mobile phones are the main information sharing method for the new generation. The devices are small, portable and cheap, you can view content in private or share with friends very easily. Content can be shared via the phone network, the internet or directly via Bluetooth, so people can share localised information within their own clique, forming their own virtual information hub. I noticed this particularly when I was teaching engineering to 16-19 year olds, they shared videos, music and information on phones leaving the internet as a secondary source, TV and magazines hardly got a look in.
Images are often a large part of content, and newer innovations such as iPad and smart paper will be welcomed, but the handy small screen phone device still has the winning formula for most.

So thinking that in some way controlling the internet will control information flow is wrong.

I became a full time journalist only a few years ago, but I am very aware that the life of that role is limited, and maybe in less than ten years it may have completely eroded.

But even with the need for a ‘speaker’ removed, I think there is a natural human tendency to elect locally respected sources of knowledge. Every web forum has one member that everyone turns to for advice.

So in the future there may still be a role for a well informed and competent communicator, the trouble is from an practical point of view that there is no intrinsic method of financially rewarding this role; information is fairly free now and hopefully there is no going back. We are all less inclined to pay for magazine articles when we can read it for free on the web, and despite the huge amount of dross and misinformation that’s about there are still plenty of well informed bloggers who report events very well, some post excellent photos and videos too.

Currently there is still a place for magazines and tv stations, because of the uncertain and variable quality of free media we need somewhere apparently reliable to turn to. But as social networks establish, an reliable free sources are clearly identified, this need will transfer from the paid for media to the free.
We live in a time of great change, traditional roles and social models are being erased from the ground up, content providers such as magazines and tv companies must work with this to make new opportunities, to resist change is to invite disaster.
Me, I’m just trying to pay my bills, and if I want people to carry on paying for my words then I suppose I will have to find something more valuable to say.

Ralph Hosier 1-November-2010